Branch: refs/heads/ehb54-issue-1055 Home: https://github.com/ehb54/ultrascan3 Commit: e5e717fb69191f44c96293079fc94662f3eee7ca https://github.com/ehb54/ultrascan3/commit/e5e717fb69191f44c96293079fc94662f... Author: ehb54 <brookes@uthscsa.edu> Date: 2026-09-08 (Tue, 08 Sep 2026) Changed paths: A us_somo/somo/doc/manual/somo/saxs_buffer_nth.html M us_somo/somo/doc/manual/somo/somo_saxs_buffer.html A us_somo/somo/doc/manual/somo/somo_saxs_buffer_conc.html A us_somo/somo/doc/manual/somo/somo_saxs_buffer_conc_load.html Log Message: ----------- somo: document the SAS Data Utility (buffer/data) module The Data Utility, opened from the Data button on the SAS I(q) panel, had no usable manual coverage: its Help button opened a "work in progress" stub dating from November 2013, and the Help buttons of its three companion dialogs pointed at pages that did not exist. Write the four pages: somo_saxs_buffer.html the module itself somo_saxs_buffer_conc.html Solution Concentrations somo_saxs_buffer_conc_load.html File Concentration Loader saxs_buffer_nth.html Select curves The main page covers loading (recognized extensions, the Conc:/PSV:/I0se:/Units: header keywords, and the rule that one non-positive standard deviation discards a file's whole error column), the selection and display tools, averaging and concentration-normalized averaging, buffer/blank/solution roles, the subtraction model and both routes to its alpha, error propagation, the non-positive-result policies, range scanning and multi-file mode, the interactive join, the cropping family including the Crop Common rounding tolerance, Produced Data and the output format, and the naming conventions of produced curves. Controls that are inert are marked as such rather than described as working: Best buffer subtraction and the Guinier checkbox are empty functions, and the join's Linear button is created disabled and never enabled. No screenshots in this pass; the manual carries no images of this module. Fixes ehb54/ultrascan-tickets#1055 Co-Authored-By: Claude Opus 5 <noreply@anthropic.com> Commit: 3b7810e83a098aa64cf61e511181ed1a924503e5 https://github.com/ehb54/ultrascan3/commit/3b7810e83a098aa64cf61e511181ed1a9... Author: ehb54 <brookes@uthscsa.edu> Date: 2026-09-08 (Tue, 08 Sep 2026) Changed paths: M us_somo/develop/src/us_hydrodyn_saxs_buffer.cpp M us_somo/somo/doc/manual/somo/somo_saxs_buffer.html Log Message: ----------- somo: fix the SAS Data Utility join fit range, default Cut and overlap bound Three defects in the interactive join of the Data Utility module. 1. join_fit_scaling(), join_fit_linear() and replot_join() selected the points to compare with q >= join_start && q >= join_end Both comparisons were >=. Since End is above Start, the condition collapsed to q >= End with no upper bound, so the automatic Fit and the RMSD readout used the tail beyond End instead of the Start-End window the two markers advertise. The scaling factor was therefore fitted over the wrong q interval, and the displayed RMSD did not correspond to the selected region. Corrected to <= join_end at all eight sites. 2. The default join Cut was computed as ( join_low_q + join_high_q / 2 ), which evaluates as join_low_q + (join_high_q / 2). The marker started off-centre and, for a wide overlap, could land outside the overlap altogether. Corrected to ( join_low_q + join_high_q ) / 2. 3. join_start() took the overlap lower bound from f_qs[ join_file ][ 1 ] where every neighbouring expression, including the ternary's own test, uses [ 0 ]. The bound was one point too high whenever the join curve started at the lower q, shifting the Start marker, the wheel ranges and the default Cut. Corrected to [ 0 ]. Drop the corresponding "current limitations" note from somo_saxs_buffer.html and state the Start-End window as what the Fit and the RMSD actually use. Fixes ehb54/ultrascan-tickets#1056 Co-Authored-By: Claude Opus 5 <noreply@anthropic.com> Compare: https://github.com/ehb54/ultrascan3/compare/e5e717fb6919%5E...3b7810e83a09 To unsubscribe from these emails, change your notification settings at https://github.com/ehb54/ultrascan3/settings/notifications